English
| Quantity: | |
|---|---|
Product Overview
This CAMC 6×4 dump truck is the brand's flagship construction transport vehicle, featuring a striking orange finish and a large-capacity rear-dump cargo bed. It is specifically designed for efficient short-haul transportation of materials such as muck, sand, and building supplies. Built on a mature chassis structure, it balances power and load-bearing performance. With 2026 factory-direct supply ensuring excellent condition, it is a cost-effective equipment for infrastructure and construction site transport scenarios.
Technical Parameters
CAMC TRUCK SPECIFICATION AND OFFER | |
NAME | Dump Truck |
BRAND/SERIES | CAMC / H9 |
CABIN | |
CAMC LHD H9 flat roof with A/C, radio, pneumatic shock absorber, pneumatic seat, blue teeth, mp3, and luxury interior. | |
ENGINE | |
Supplier | CAMC |
Model | CM6D18 375 50 |
Fuel type | Diesel |
Rated power/horsepower（kw/hp） | 276/375 |
Rated speed(rpm) | 1900 |
Displacement (L) | 9.84 |
Emission Standard | Euro 5 |
Cylinders | 6 |
Controller type | Mechanical |
TRANSMISSION | |
Supplier | FAST |
Model | 12JSD180T（PTO） |
Speed ratio | 12 |
CHASSIS | |
Drive type | 6×4 |
Overall dimension (mm) | 8800x2550x3700 |
Wheel base(mm) | 3900+1350 |
Kerb Weight (kg) | 12300 |
Rated GVW/ GVW (kg) | 25000 |
FRAME | |
Size (H*W*T) | Height:310mm，Width:90mm，Thickness:8mm+5mm (Double) |
Front axle | ISUZU technology steering axle with double T-cross section, Rated capacity:7.5T |
Rear axle | Mercedes-Benz technology 16T casting axle , with double reduction and differential locks between axles， Rated capacity:16T |
Ratio:4.769 optional:3.867, 4.267,4.769,5.263 | |
Spring | 9/9/12 |
Tyre | 12.00R20 Steel tire,10+1 pieces |
Operation Guide
1.Pre-Start Inspection：Carefully check whether the tire pressure meets the standard, whether the hydraulic oil level is within the standard range, and confirm that the cargo bed is fully reset without deviation.
2.Driving Precautions：Strictly prohibit overloading. Be sure to slow down when turning or driving on ramps, and keep a safe distance from the vehicle in front.
3.Unloading Operation Process：Park on a flat and solid ground, pull the handbrake tightly → unlock the cargo bed locking device → slowly operate the hydraulic lever to lift the cargo bed → reset the cargo bed after unloading and check again whether the locking state is firm.
4.Daily Maintenance Points：Clean the air filter regularly, inspect the tightness of the hydraulic system pipelines, and replace the engine oil in a timely manner according to the specified mileage.
Product Advantages
1.High Adaptability: 6×4 drive layout + large-capacity cargo bed, suitable for heavy-load transportation of various construction materials, with more stable passage in complex working conditions.
2.Efficient Unloading: Fast-response hydraulic dump system enables smooth unloading process, greatly improving transport turnover efficiency.
3.Durable & Reliable: The body is made of high-strength steel, and key components are reinforced, adapting to high-frequency operation scenarios with longer service life.
4.Controllable Cost: The mature powertrain balances power and fuel economy; factory-direct supply reduces procurement costs; the wide after-sales network ensures convenient maintenance.
Production Process
Company Profile
CAMC is the national priority production and research development base of heavy truck, special purpose heavy vehicle and spare parts, which is also the state mainly supports enterprise. CAMC was found in 1970s and we are the only one truck enterprise in China which is capable of produing everything by our own including engine, gearbox, axles, chassis, cabin and so on.
FAQ
Q:How about the warranty?
A:2 years.
Q: Do you have ISO certificate?
A: Yes, we have. Please contact us to get our certificates.
Q: How about the delivery time?
A: Most of our trucks have stock, we can deliver to you within 7 days, if specially ordered, normally we need around 30 days for production.
Q: How many units of truck does your factory produce per year?
A: Almost 100000 units. Nearly 8500 units per month.
Q: How do you control the quality of product?
A: Our Factory has standard production workshop and gets ISO CCC BV certificates. Our workers are well trained. Every unit of product undergoes a rigorous inspection process.
Q: How about your product after-sales service system?
A: Our main export countries have accepted after-sales service, some countries use the third party service.
Q: Do you accept custom order? What's is your MOQ order?
A:Yes, we do. Our MOQ is 1 unit.
Q: What's the payment terms?
A: By T/T or L/C at sight.
Q: How about shipment?
A: 20FT container, 40FT container, 40FT high container, open-top container, flat bed container, Ro-Ro ship or bulk ship according to the size the products.
Product Overview
This CAMC 6×4 dump truck is the brand's flagship construction transport vehicle, featuring a striking orange finish and a large-capacity rear-dump cargo bed. It is specifically designed for efficient short-haul transportation of materials such as muck, sand, and building supplies. Built on a mature chassis structure, it balances power and load-bearing performance. With 2026 factory-direct supply ensuring excellent condition, it is a cost-effective equipment for infrastructure and construction site transport scenarios.
Technical Parameters
CAMC TRUCK SPECIFICATION AND OFFER | |
NAME | Dump Truck |
BRAND/SERIES | CAMC / H9 |
CABIN | |
CAMC LHD H9 flat roof with A/C, radio, pneumatic shock absorber, pneumatic seat, blue teeth, mp3, and luxury interior. | |
ENGINE | |
Supplier | CAMC |
Model | CM6D18 375 50 |
Fuel type | Diesel |
Rated power/horsepower（kw/hp） | 276/375 |
Rated speed(rpm) | 1900 |
Displacement (L) | 9.84 |
Emission Standard | Euro 5 |
Cylinders | 6 |
Controller type | Mechanical |
TRANSMISSION | |
Supplier | FAST |
Model | 12JSD180T（PTO） |
Speed ratio | 12 |
CHASSIS | |
Drive type | 6×4 |
Overall dimension (mm) | 8800x2550x3700 |
Wheel base(mm) | 3900+1350 |
Kerb Weight (kg) | 12300 |
Rated GVW/ GVW (kg) | 25000 |
FRAME | |
Size (H*W*T) | Height:310mm，Width:90mm，Thickness:8mm+5mm (Double) |
Front axle | ISUZU technology steering axle with double T-cross section, Rated capacity:7.5T |
Rear axle | Mercedes-Benz technology 16T casting axle , with double reduction and differential locks between axles， Rated capacity:16T |
Ratio:4.769 optional:3.867, 4.267,4.769,5.263 | |
Spring | 9/9/12 |
Tyre | 12.00R20 Steel tire,10+1 pieces |
Operation Guide
1.Pre-Start Inspection：Carefully check whether the tire pressure meets the standard, whether the hydraulic oil level is within the standard range, and confirm that the cargo bed is fully reset without deviation.
2.Driving Precautions：Strictly prohibit overloading. Be sure to slow down when turning or driving on ramps, and keep a safe distance from the vehicle in front.
3.Unloading Operation Process：Park on a flat and solid ground, pull the handbrake tightly → unlock the cargo bed locking device → slowly operate the hydraulic lever to lift the cargo bed → reset the cargo bed after unloading and check again whether the locking state is firm.
4.Daily Maintenance Points：Clean the air filter regularly, inspect the tightness of the hydraulic system pipelines, and replace the engine oil in a timely manner according to the specified mileage.
Product Advantages
1.High Adaptability: 6×4 drive layout + large-capacity cargo bed, suitable for heavy-load transportation of various construction materials, with more stable passage in complex working conditions.
2.Efficient Unloading: Fast-response hydraulic dump system enables smooth unloading process, greatly improving transport turnover efficiency.
3.Durable & Reliable: The body is made of high-strength steel, and key components are reinforced, adapting to high-frequency operation scenarios with longer service life.
4.Controllable Cost: The mature powertrain balances power and fuel economy; factory-direct supply reduces procurement costs; the wide after-sales network ensures convenient maintenance.
Production Process
Company Profile
CAMC is the national priority production and research development base of heavy truck, special purpose heavy vehicle and spare parts, which is also the state mainly supports enterprise. CAMC was found in 1970s and we are the only one truck enterprise in China which is capable of produing everything by our own including engine, gearbox, axles, chassis, cabin and so on.
FAQ
Q:How about the warranty?
A:2 years.
Q: Do you have ISO certificate?
A: Yes, we have. Please contact us to get our certificates.
Q: How about the delivery time?
A: Most of our trucks have stock, we can deliver to you within 7 days, if specially ordered, normally we need around 30 days for production.
Q: How many units of truck does your factory produce per year?
A: Almost 100000 units. Nearly 8500 units per month.
Q: How do you control the quality of product?
A: Our Factory has standard production workshop and gets ISO CCC BV certificates. Our workers are well trained. Every unit of product undergoes a rigorous inspection process.
Q: How about your product after-sales service system?
A: Our main export countries have accepted after-sales service, some countries use the third party service.
Q: Do you accept custom order? What's is your MOQ order?
A:Yes, we do. Our MOQ is 1 unit.
Q: What's the payment terms?
A: By T/T or L/C at sight.
Q: How about shipment?
A: 20FT container, 40FT container, 40FT high container, open-top container, flat bed container, Ro-Ro ship or bulk ship according to the size the products.
